Helping to Keep Your Workers Safe with Fall Protection Systems and Equipment

The city of Raleigh resides in the state of North Carolina and North Carolina has an approved OSHA State Plan called NC OSH. Regarding fall protection, NC OSH refers to OSHA CFR 2019 for all applicable fall protection requirements.

Along with NC OSH, the city of Raleigh follows the North Carolina Building Code (NCBC). NCBC adheres to the International Building Code standards, but applies amendments that are relevant to the state.

Understanding Raleigh Fall Protection Requirements

OSHA Standard Interpretation - Do I follow OSHA or local building code in Raleigh?

The strictest rules must be followed. Where local codes are in effect, they are generally more specific and more stringent than applicable OSHA regulations. Compatibility with OSHA regulations is seldom an issue. (source)

OSHA 1910.5(c)(1) - What OSHA code applies in Raleigh?

If a particular standard is specifically applicable to a condition, practice, means, method, operation, or process, it shall prevail over any different general standard which might otherwise be applicable to the same scenario. (source)

NCBC 1015.2 - Where is guardrail required in Raleigh?

Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps, landings and retaining walls that are located more that 30 inches measured vertically to the floor or grade below at any point within 36 inches horizontally to the edge of the open side. (source)

NCBC 1015.2 - At what height do I need fall protection or guardrail in Raleigh?

Guardrails are required on any elevated walking surface above 30 inches. (source)

OSHA 1910.29 - What can a guardrail be made out of in Raleigh?

Guardrails, as long as they comply with all applicable standards, may be made out of any material. (source)

NCBC 1015.3 - How tall does rooftop guardrail need to be in Raleigh?

Guards can not be less than 42 inches high. (source)

OSHA 1926 Subpart M App B - How far apart can guardrail posts be in Raleigh?

Guardrail posts may not be spaced more than eight feet apart. (source)

OSHA 1926.502(b)(2) - Do I need a mid-rail in Raleigh?

Midrails must be installed between the top edge of the guardrail system and the walking/working surface when there is no wall or parapet wall at least 21 inches high. (source)

OSHA 1910.29(k) - When do I need a toeboard in Raleigh?

Toeboards are required when there is danger of items falling from an elevated walking-working surface onto workers below. (source)

NCBC 1607.8.1.1 - What are the load requirements for rooftop railing in Raleigh?

Handrails and guards must be designed to resist a concentrated load of 200 pounds. (source)

OSHA 1910.29(b) - Can I use a non-penetrating guardrail in Raleigh?

Yes, as long as it complies with all other guardrail standards. (source)

NCBC 1014 - Can guardrail serve as handrail in Raleigh?

Guardrails and handrails serve two different purposes and have different requirements. A handrail may be attached to a guardrail, but they are not one in the same. (source)

NCBC 1015.2 - If my rooftop is lower than 22 feet but I have mechanical equipment close to the edge, do I need rooftop railing in Raleigh?

Guards must be located along open-sided walking surfaces, including equipment platforms, that are located more that 30 inches measured vertically to the floor or grade below any point within 36 inches horizontally to the edge of the open side. (source)

NCBC 1015.7 - If my rooftop is lower than 22 feet but I have a roof hatch close to the edge, do I need rooftop railing in Raleigh?

If you have a roof hatch located within 10 feet of the roof edge, the roof access or roof edge must be protected by guardrail. (source)

OSHA 1926.501(b)(4)(i) - When is protection required when falling through a hole in Raleigh?

Employees must be protected from falling through holes, including skylights, that have more than a 6 foot drop, by personal fall arrest systems, guardrails, or covers. (source)

Popular Fall Protection Products in Raleigh

Have any Questions about Fall Protection?

We pride ourselves on not being "just another company trying to sell you something". We take safety seriously and we want to partner with you to make sure you receive the right fall protection solution that meets compliance requirements, protects your workers while they work at height, and reduces liability for your company.

Michael Hannah at desk
Michael Hannah
Fall Protection Specialist
Or call a specialist at:
1.866.527.2275

Contact Information

Michael Hannah
Fall Protection Specialist

Shopping Cart

Show Pricing

Option available in footer.